This forum is for users to exchange information and discuss with other users about a TMPGEnc product.
In case you need official support, please contact TMPG Inc.
Pegasys Products BBS [ Sorted by thread creation date ]
Becuase I store numerous clips on DVD's in VCD format, and sometimes need to create DVD's of samples of them, it is better to encode them CBR, so that I get Smart Rendering. Is there anyway of making CBR the default, so that I won't forget to do it for EVERY track? I have a nasty suspicion the answer is no!!
I have a large number of DVD's burned with VCD content. I cometimes need to burn a DVD with samples of these. They all need Full Rendering, which is very time consuming. Is there some way I can get around this so that it will use Smart Rendering?
TAW4 might not be getting the correct aspect ratio for the VCD video. A VCD I have is should be set to Pixel 10:11 (NTSC 4:3), but TAW4 set it as Pixel 12:11 (PAL 4:3). Once I set it to the NTSC aspect ratio, smart rendering kicked in.
Likewise, if your VCD files actually are PAL 4:3, then you'll need to make a PAL DVD for smart rendering to be activated.
You can change the aspect ratio setting for your clip in the clip properties tab of the clip editing window.
Using PAL. I have a clip encoded as VCD. Using GSpot, I see the pixel aspect ratio is 12:11. Load it into TAW4 and check with clip properties - par is 12:11. It is using smart rendering.
Burn a DVD. Load the clip into TAW4 ripping from the DVD. Clip properties show par 12:11. Rename the ripped dvddata file to mpg and check with GSpot - par is 12:11. Using full rendering.
With the original VCD clip and the ripped clip loaded into TAW4, I cannot see any difference in clip properties, apart from the tags MPEG file reader and DVD reader. Also, the original clip shows bit rate (1150 kb/s), but the ripped clip doesn't show bit rate. Maybe I should set the track settings to CBR when I burn VCD files? (I'm going to have no end of problems remebering to do this each time!)
Looks like you're right. I ran a few tests of this myself and it looks like TAW4 is changing the file type to MPEG-2 if you select VBR. Unfortunately, a MPEG-2 VBR at VCD resolutions is not compliant with the DVD-Video format, which is why it will then be full rendered if you try to import the DVD.
So there's two options from there:
1) Change the resolution to a regular DVD-Video resolution (720x480, 720x576, etc.), making it like typical DVD-Video footage. However, increasing the size of the image will also increase the file size, so you wouldn't be able to fit as much on one disc
or, (probably the better option)
2) Selecting CBR will keep the file as an MPEG-1 and retain its ability to be Smart Rendered for future projects.
HI.
im trying to import an M2TS video file that is using the VC-a video codec.
But when i try to add file to tmpeg ex4 i get error stating it can not open the file.
It seems to be a VC-1 problem and not an M2TS problem as i can open other m2ts files with 264 codecs...
Does anyone have a fix so i can import vc-1 coded videos into tmpegencxpress4?
preferably without having to load in a pile of codec packs..
i could have sworn tmpx4 supports VC-1
I have the latest copy of TMPGEnc and have recently run into some Canon Digital camera files that are .AVI's and are using the Motion Jpeg Codec. So when I add them into a new Project, TMPG will report that my Morgan-Multimedia Codec has expired and it can only do the audio part of the file and not the video. Any suggestions?
>Hey guys!
>
>I have the latest copy of TMPGEnc and have recently run into some Canon Digital camera files that are .AVI's and are using the Motion Jpeg Codec. So when I add them into a new Project, TMPG will report that my Morgan-Multimedia Codec has expired and it can only do the audio part of the file and not the video. Any suggestions?
>
>Thanks!
>
>Knuckles
Hi, here is the situation, lets say I compile a dvd video, but I want to burn it at later time (not right after the convertion to dvd), I can't find a way in Authoring Works 4 that would allow to burn the dvd, is it possible? Will it work if I just burn the audio_ts video_ts folders using the built in disc burner, or do I have to use some other software for this. I think this is a fairly simple operation that should be built in the software.
Just output the project and not burn it. You can always burn the video_ts folder later with the disc writing tool. The disc writing tool can be accessed in the Start stage.
Once in the disc writing tool, use the "Add folder" button to select the folder on your hard drive that contains the Video_ts and Audio_ts folders, then you should be ready to burn.
The file has 2 language italian and english italian is audio 1 and english is audio 2 but I can only get the italian and not the english what am I doing wrong? I've tried 4 or 5 times only get the same result.
I found TMPGEnc 2.5 does not read .wmv and .avi files as video source. Could be a setting matter or there is a limitation of this software ? Grateful for a clue.
This is quite a lamer question... but I'm somewhat mystified by the `cut-editor'.
After loading a clip of recorded TV, I expected to be able to remove the commercial easily as advertised on tmpgenc home pages.
However, I have not been able to see how to do the most basic step. How to make a selection. The help file mentions things that can be done with a selection in many places.. but appears never to tell how to make a selection.
The tools offered.... Keyframe and clip-split appear to have nothing to do with selecting. Setting either before and after an unwanted section does not select it.
Ctrl mouse drag does not select Shift does not select.
AFter setting keyframes or split frames .. If I press the scissor tool, I'm told the entire clip is selected and I cannot proceed.
Clearly I'm missing some really basic information here.
Googling for `Tmpgenc Mpeg editor Tutorial'... hasn't turned up anything that looks useful either. It turns up dozens of illegal downloads, rapidshare etc etc cracks and so on... but nothing that looks like a good turorial.
So what am I missing... in order to do basic selecting?
1.) Navigate to the first frame you want to cut, then click the "set start frame button" (bottom row, to the left of the scissor button).
2.) Navigate to the last frame you want to cut, then click the "set end frame button" (bottom row, to the right of the scissor button).
3.) The section you want to cut should now be the only thing selected (it's the blue section in the slider and the frames in the thumbnail film strip are highlighted blue/purple).