I downloaded virtual dub, but cannot load the film in order to rip the audio, as when i try to open the file, I get an error message that lasts for approx .3 secs..so not sure what it is..or when I try to "capture" the filke..I get an error message saying that no capture device is available..any ideas please.

What is it you are trying to do?
Capture or load an AVI???

It seems your are trying to start the capture program to just load an AVI!
The capture program is used to capture 'live' images from a source such as a capture card. If you don't have one installed then you get the error you have received.

To load an AVI into Virtualdub simply click File>Open Video file.
You must also make sure you have the appropiate codec installedto decode the file or Virtualdub will reject it.

ASHY

>What is it you are trying to do?
>Capture or load an AVI???
>
>It seems your are trying to start the capture program to just load an AVI!
>The capture program is used to capture 'live' images from a source such as a capture card. If you don't have one installed then you get the error you have received.
>
>To load an AVI into Virtualdub simply click File>Open Video file.
>You must also make sure you have the appropiate codec installedto decode the file or Virtualdub will reject it.
>
>ASHY

>>What is it you are trying to do?
>>Capture or load an AVI???
>>
>>It seems your are trying to start the capture program to just load an AVI!
>>The capture program is used to capture 'live' images from a source such as a capture card. If you don't have one installed then you get the error you have received.
>>
>>To load an AVI into Virtualdub simply click File>Open Video file.
>>You must also make sure you have the appropiate codec installedto decode the file or Virtualdub will reject it.
>>
>>ASHY

Hi!

Is it possible to make a .ini .txt or whatever-file to make a german tranlation for the TMPGEnc. There is only japanese or englisch to select.

Thanks

pHi

No you would have to hack the program exe.

ASHY

Its just that I find it a little bit annoying having to select a file, put the options then having to batch encode again for another file. (This will take me forever to select one by one for my anime's)
How about letting us select multiple files and putting the same options for them in the batch encode in later versions? (With the estimated file size for every of them too...)

http://www.innsys.com.au/doylie/cat_Development/TMPEG_Batcher/TMPEG_List.asp

ASHY

I used to use a matrox rt2000 pci card with premiere and I used tmpgenc and all worked fine.

However, I took the card out and started from scratch, installed premiere 6.5. Created the typical Microsoft DV avi file. Now tmpgenc says that it "can not open, unsupported."

HUH?!?!?


Anyone?!?!

Thanks!

Craig L.

"options" to "Enviromental Settings" to "Vfapi Plugins" and raise the "Direct Show" to "2"...

I have the same problem (Win2000, premiere 6.5)

I direct the output of premiere to my avisynthtransfer-file.
After loading in TMPGE and pushing START, I get the message:
File E:avisynthtransfer.avs can not open, or unsupported

(I did change the priority setting for direct show to 2. No change.)

Other ideas?

Thanks

I use DVD2SVCD to rip a DVD and TMPG to encode the results. I then burned the cue(bin) file using Nero and my Plexwriter burner. The result is a slightly jerky video on the CD. I have another stand alone program that burns the SVCD without jerkiness. I suspect I need to make some type of change in TMPG but once I start DVD2SVCD, the process runs all the way through to creating the cue files without stopping at the TMPG encoding screen. I am using the trial version of the TMPGEnc Plus encoder, if that makes any difference.

Any thoughts on how I can correct this one minor problem. Thank you in advance for any help.

Please add the ability to load and process *.tpr files to the Merge & Cut feature.

What?

Have you ever looked inside a tpr file?
How can you expect a .tpr file to be processed in the Merge&Cut feature?

A .tpr file is a predefined set of instructions and settings created by *YOU* including any cut points you have made.
There are no settings which could be beneficially changed by the Merge&Cut feature and even if there were what would be the point?
It's just as easy to create another .tpr file to be processed in the first place.

ASHY

Hi! I did look through the board before posting, but with my luck, this question has already been asked and answered!
I've tried to convert several avi files to mpg, but I keep getting the same error:
Read error occurred at adress 00402F40(this varies) of module 'TMPGENC.EXE' with 1048758C(this varies).
I'm really hoping someone can tell me if this is a problem with my computer or if there is a setting within TMPGENC that I can change to get it to actually work.
Thanks in advance!!! :)

Your AVI's are most likely downloaded off the net and are probably corrupt some way.
Either that or you have some dodgy memory sticks in your machine. The first is more likely.

Try raising the priority of the 'directshow file reader' to 2 in the VFAPI plugins.

If that doesn't work try frameserving the file from Virtualdub.

ASHY

Hi,

sorry for my bad english. I have the same problem like DyanJae. TMPGEnc shows the same error messages when i tried to convert a avi who i made with DVD2Avi. But the errors came first, as i change the Processor (1800XP+ to 2200xp+) But i had format c: ... it can't be a memory error
. This problem i've read in many other boards too and no one got a answer. Can someone help here? Please write in a pidgin english for me to understand

:o)
Richi

Please add the ability to load and process *.tpr files to the Merge & Cut feature.

I need some assistance. I have an AVI file that I am trying to convert to MPEG, so that I can burn it to a Video-CD. Right now, this is the properties of the AVI file on my computer...

Audio Format:

MPEG Layer-3,56 kBit/s, 24,000 Hz, Stereo

Video Format:
352X240, 24 bits, 51914 Frames, 14.985
Frames/Sec, 44 KB/Sec, MS-MPEG4 V3

The movies plays file in my Windows Media Player. Though, when I open TMPG Enc, it will not encode right. Even though I select the file for both "audio" and "video", it encodes a new "MPEG" file in the same folder, but all I get is audio. If I encode it, "video" alone.. I get a black picture, no sound.

What's wrong?

Go to "File" to "Enviromental Settings" to "Vfapi Plugins" and Raise the "Direct Show File Reader" to "2"..This usually fixes this Problem...

I heard that Nero can burn AVI files or MPEG files to VCD/SVCD right?

hi,
i use tmpgenc, but i didn't find out the correct settings for svcd to fit a cd correctly...hope you know what i mean, my english is not so good...

when i use a bitrate calculatort, and use cinemacraft i always get the correct size for the endmovie...
with tmpgenc the files always are shorter...
example: cinemacraft = 798 mb
tmpgenc = 700 mb
(for svcd)...

this is a diffrent bout 100mb and i use the same settings (2-pass) for both programms...just cce has the correct size the calculator told me..

okay, example:
encoded with tmpgenc 2min04sec (for a test)

standard template with wizzard (2pass - avarage 2200, max 2520, min 300)
should be 36,72mb (said tmpgenc...)
real: 32,4mb

next try 2-pass, avarage 2200, max 2520 min 1200 enable padding)
same as the first, 32,4mb

changed gop from 1,7,2,1 (standard tmpgenc) to 1,5,2,1
= same settings as 2nd
= 33,5mb

test with cce
2pass, av 2200, min 1200, max 2400
= 37,15mb

so it seems to be a gob problem...
anyone good sites for learning about gop?

I doubt this is a GOP problem. The size difference from 32.4mb to 33.5mb is probably due to the fact you have changed the GOP structure from 1,7,2,1 to 1,5,2,1.
What you have done is decreased the amount of 'P' frames and shortened the GOP size which in turn is going to create more 'I' frames because there will be more GOPS in the MPEG and seeing as 'I' frames require more bitrate and don't compress as well as 'P' frames the 1.1mb increase is understandable.

ASHY

In addition to above.

The default GOP structure of CCE uses 1,4,2,1 = 15 frames in a GOP.
With TMPG 1,7,2,1 = 24 frames and the default setting for SVCD is 1,5,2,1 = 18 frames.

Looking at the above figures and the explanation in the previous post you can see there will be more GOPs and therefore more 'I' frames in the CCE encoding thus increasing the file size.

ASHY

big thx...
changed to settings from cce (1,4,2)...
now i will change the max number offrames to 15
(default was 0)...
hoping to fit the cd in the future correctly...

but i don't understand the max number of frames..is 15 the correct setting?
i don't want to make svcds with high compression, i want to get the best quality for svcd...

Ok I have been looking into this problem and here are some observations.

Using the Project Wizard:
Firstly I used your settings for a 2.04 min clip - 2-pass, average 2200, max 2520 min 1200 enable padding - to create an MPEG with TMPG.
The audio was set at a bitrate of 224 kb/s ( for some reason in v2.58 the bitrate is set out of standard at 128kb/s)

TMPG reported the final size as 36.2mb the actual size was 35.8mb, so you can see TMPG was pretty close.

Observing the GOP structure which TMPG set for this was 1,5,2,1

Using the same settings for both CCE and TMPG:

2-pass, average 2200, max 2520 min 1200 enable padding
GOP = 1,4,2,1
audio bitrate = 224

Results:

TMPG = 35.8 MB
CCE = 36.2mb

It seems somewhere along the line there is a miscalculation on your part or a setting wrong.
As you can see the TMPG and CCE results are more or less the same.

ASHY

thx, but i can't see the gop-settings of cce...they're named other
like N, N/M...??!!
the settings of cce are N:3 N/M:5 gopheader every (locked) 1, SEQ Header 1..

and maybe it's because i'm using tmpgenc and cce for pal-svcds? (i'm german...)
so i always use 480x576, non-interlace/progressive (also in advandec mode)
16:9 (for most dvds)

my next test was the same film with the same length (it's "nothing to lose" - one of my favourite films) the biginning of the film, it starts with movie...

2.04min (3121 frames)
(i will cut him later at 47:30) and will put it on a 700mb (80min) disk, so the bitrate calc gave me 2088)
i used 2pass, avarage 2050, max 2400 min 1200 enable padding, max pass 2-pass, video format pal, non-interlace, yuv 4:2:0, dc 10, motion high quality
advanced progressive, field b, 16:9, fullscreen (audio 224...)
gop 1, 4,2,1 max number of frames in gop 15

result: 31,7mb

saved as a tpr, used vfapi reader codec for frameserving (no audio, doing it with tmpgenc ;_) and loaded it in cce 2.64, settings mpg2 multipass -2pass av: 2050, min 1200, max 2400 (gop settings as written, 3,5...?)

result (after multiplexing with tmpgenc): 34,2mb !!!

if i calculate these results for 47:30 (2850seconds)

tmpgenc about 729mb for 47,30min
cce about 786mb !! and that's what i want to have with tmpgenc...
and that's what the bitrate calc told me...

so there MUST be something wrong with my settings...?? !!
help again?

First of all if you know how to frameserve to CCE from TMPG why would you want to encode in TMPG.
CCE is better at MPEG2 encoding and quicker.

Secondly, if you are encoding from DVD to MPEG2 then your source and output should be set to interlaced not progressive unless you have used ForcedFILM in DVD2AVI.

As for your differences in file size I can't really see the problem. I'm using v2.510 of TMPG.

As for CCE the default audio setting is 256 kb/s. This should be changed to 224kb/s

Also CCE has a default VBV buffersize of 224 which can't be changed.
This will have a slight effect on the file size also if it's not set the same in TMPG.


ASHY

i'm using tmpgenc because cce cost so much, or could you sent me a free version? ;-) i just wanna test cce if its really soooo good, but i can't see any different between tmpgenc and cce encoded films...

and the svcds i made with tmpgenc are really great...
but i want to optimize my settings with tmpgenc...

with dvd2avi i only encode the sound (amd multiplex it tmpgenc) and for pal all settings are progressive (or not?)..

>with dvd2avi i only encode the sound (amd multiplex it tmpgenc) and for pal all settings are progressive (or not?)

DVD2AVI cannot encode sound except to a wav, so how are you encoding the audio.
How are you importing your DVD's into TMPG for encoding if you are not using DVD2AVI?

As for PAL. PAL is an interlaced format used in Europe just as NTSC is an interlaced format used in the US.

The only time your output should be progressive is if you are creating VCD all other formats such as DVD,SVCD require to be interlaced if the intended output is TV.

ASHY

creating wav file with dvd2avi and put it as audio souce, then say "audio only" and convert it to mp2 file...

and german dvds ARE progressive...

Right Frasier it seems you know little about the DVD format or MPEG2 encoding.

Let me explain.

DVD has to conform to the standard as set by the 'DVD Forum' and the
'Moving Picture Experts Group (MPEG) ISO/IEC JTC1/SC29 WG11'

Almost all DVDs are stored as progressive, but playback as interlaced which is required by the DVD standard.

Now I'll tell you why.

DVD's have a process called 'telecining' or 3:2 pulldown applied to them. In short what this does is add flags to a DVD encoding to tell the player to repeat a sequence of fields every second, this converts a 24/23.976 fps progressive movie to a 29.97 fps NTSC interlaced movie as required by the NTSC TV standard.

PAL movies have a similar process but uses 24:1 pulldown with 4% speed up.

Both of these processes require each progressive frame to be split into fields so the fields can be repeated by the player. 2 fields make up 1 frame this is what we refer to as interlacing.

Without the frames being split into fields and thus interlaced the process would not work.

DVD2AVI can remove the 3:2 pulldown flags and return the interlaced movie back to it's progressive state by using it's ForcedFILM option.
For a PAL movie this is not required even though it is interlaced as the sequence of fields does not shift unlike the fields in an NTSC movie using 3:2 pulldown.


Here is a clip from the Distronics DVD and MPEG2 encoding specs page.
Pay particular attention to the last paragraph which is highlighted.

MPEG-2 Video Encoding
The MPEG-2 specification (ISO 13818) was designed for broadcast TV and
other applications using interlaced images. It provides higher picture quality
than MPEG-1 but using a higher data rate. At lower bit rates, MPEG-2
provides no advantage over MPEG-1. At higher bit rates (above about 4
Mbits/s) MPEG-2 should be used in preference to MPEG-1. Unlike MPEG-1,
MPEG-2 supports interlaced TV systems and Vertical Blanking Interval (VBI)
signals.
MPEG-2 also allows variable bit rate (VBR) for lower bit rates without loss of
picture quality. VBR encoding uses more data to code those parts of a video
sequence which are more complex and do not compress well. CBR, constant
bit rate, encoding, means that the video data rate must be high enough to
encode the video well. For short videos, where disc capacity is not an issue,
CBR, at as high a bit rate as possible, is the better choice.

>MPEG-2 uses the same frame types as MPEG-1 except that each frame
comprises two interlaced fields. Also each group of pictures (GOP) is 15 (PAL)
or 18 (NTSC) frames in length maximum.

I hope now you understand.

ASHY

Here is some nice info on 3:2 pulldown.

http://www.dlpstore.com/techguide/pulldown_2.asp?page=3

uh thx,
ok, source progessive...encode interlace...

Unless you have used the ForcedFilm option or IVTC (NTSC only) then both your input and output should be set to Interlaced in TMPG.
Even though DVD's are stored as progressive frames on the disk the actual output will be interlaced because of the pulldown.

ASHY

Here is proof that your DVD is interlaced.

Download this program and load one of your VOBs into it.
It will tell you all the details you need to know of the file.

http://www.tecoltd.com/bitratev.htm

ASHY

What are correct setting to make sure that when you encode your file will work for a VCD. Every time I encode a .WMV file i either get a wrong frame rate or size or system clock reference. Thanks in advance

Just load the correct VCD template and encode.

ASHY

When I use simple De-multiplex to convert the AVSEQ01.DAT from CD to a mpeg1 and audio file. I do not get the whole movie. This happens in Win2K. I tried it in Win98 and I don't have that problem. I am running TMPGEnc 2.51 plus. What gives?

Try makeing the Dat into a Mpeg file with something like VCDEasy or VCDGear then De-Muxing the Mpeg file in tmpgenc..