I download loads of films using Kazaa. I wanted to put these in VCD or SVCD format so as to free up my Hard Drive. When I use TMPG Enc I am using the same source *.avi file for both video and audio. I get great quality video encoded in bout 4hrs but there's no sound. Do I need to extract the sound from the *.avi file first and when I choose my source video and audio file make the *.avi file the video source and the *.? file the audio source.

same problem can you help me if you find out first.I'll do the same

Quite a few of the divx films on kazaa have mp3 variable bitrate audio.
TMPGenc only supports constant bitrate try using virtualdub to extract the audio to a pcm uncompressed wave file then select the wave file in tmpgenc.

Did you compare CCE against their new GOP structure and new Quantization Matrix? This was just released less than a week ago!!

I just downloaded TMPGEnc v2.59 and unzipped the file. First question: why is there no install/setup file? I then tried running TMPGEnc.exe. It runs,but after specifying my input and output files and trying to proceed, I got the following error message: Can't load "P3Package.dll"

Can anyone help? Greatly appreciated.

Thanks,
Sig

TMPGENC Is a Standalone application so there is In Installer..But you have to extract ALL of the Files in the Zip File in the same folder..You odviously don"t have them in the same folder or you wouldn"t be getting the P3P Package error...

I download loads of films using Kazaa. I wanted to put these in VCD or SVCD format so as to free up my Hard Drive. When I use TMPG Enc I am using the same source *.avi file for both video and audio. I get great quality video encoded in bout 4hrs but there's no sound. Do I need to extract the sound from the *.avi file first and when I choose my source video and audio file make the *.avi file the video source and the *.? file the audio source.

Are they divx avis with vbr mp3 audio ? I had same problem and if you open avi in Virtualdub then extract audio to wav, then use that as audio source in encoder it should be ok . To check, go into Source range, then tick Display Audio and yuo should see audio waveform.
ps. you could also use virtualdub to frameserve to encoder.

No sound is not only caused by mp3 VBR by AC# sound,too.
Open your file in VirtualDub, go to file menue. Through that access the file information and see the sampling rate. If it tells you 48000, then you have to go to audio menu, select full processing mode (this one you have to do no matter what), then audio/conversion, change sampling rate to 44100, precision to 16 bit.
You will get a decent output which will be supported by TMPGEnc.

I mean, AC3 sound, of course,sorry for the typo.

I got a vcd inverted, top is on botton and vice versa, can I fix it with TMPGenc?, how?

Are you using DIVXG400?
To maka it easier for you to understand, let me ask you this:
Once you run a video file, do you see a small "monitor" icon appearing in the tray menu on the bottom right side of your screen?
if yes, double click on it.
There you will see something called "Force vertical flip".
Play with the options - you totally have 4 choices - until your video file goes back to normal.
Note, if you do have the mentioned above program, you don't have to worry, there is nothing wrong with your file, meaning that if you burn it ass a VCD, then your stand-alone player will accept it with no flipping.

Hi

i have a few problems with this program.

First of all, when i decode there is no sound...the sound source is ok...

Second: i encode much stuff with subtitels but the subtitels are not readable because the arent completely on the screen...which format is the best to get the whole picture on the screen so that i have also the subtitles to read?
On the WMP its all ok with the picture...
I am using PAL TV (Europe)

Hope u can help a newbie

Thank you

BTW: i read the FAQ!!!

The audio format in the AVI file is not being read By Tmpgenc So you have to extract the Audio from the AVI file to a WAV file with Something like "Virtual Dub" and use the WAV file as the Audio source..To arange the Frame in the Screen so you can see the while frame you Should have the "Video arrange Method" set to "Fullscreen(Keep aspect Ratio)" But if for some reason you aren"t happy with the results The use "Clip Frame" settings in the "Advanced Settings"...

Thank you so much...it works with the subtitles :)

And some Movies have sound and some not.....i wonder why?

I have just started working with TMPGEnc, which after 2 days finally got to do what I wanted it. The only thing I do not know how to do is how to get the subtitles in. Can anyone tell me how to do this ?? I am using SmartRipper and DVD2AVI_1.77.3 as well . Thanks !!

You need to use VOBSUB with Virtualdub. This will use the subs in the original DVD and frameserve them to TMPG.

If you need info how to do this see VCDhelp.com

ASHY

Hello!

After transcoding a MPEG-PS (PAL) file in MPEG file for "Sonic DVDIt!", I get
following message: "Each GOP header must be preceded by a sequence header".
What going wrong or where is my error?

How is the correct setting in TMPGEnc for a PAL-DVD MPEG file?

Axel

In the "settings" go to "GOP" and set the "Output interval" to "1" this should work...With DVDit every gop has to have a Sequence header..It is a Very picky program...

Sorry, it doesn¡­t work. I have a DVB-MPEG-stream and after the transcoding with the setting 1,2,3,1,15 (GOP Structure) it doesn¡­t work. Where is error??
In DVDIt! or in TMPCEnc???
Axel

I'm trying to convert an AVI file to MPEG, but when I convert it, there is no video, only audio. During the conversion, there is no video shown on the screen.
I thought that it is "normal", but when the conversion is finished, there is really no video. I tried converting other AVI files and it was converted easily with no problem. I tried converting the first AVI file but then I got the same result: no video, only audio. Is there a prblem with the AVI file? Can I fix it with TMPGEnc? I hope u can help me? Thanks.

Try this ..Go to "options" to "enviromental settings" to "Vfapi Plugins" and raise the "Direct Show" to "2"...

Probably your AVi file is old DIVX codec such as 3.12 alpha, for example.
If you are not sure what codec it is, open it with VirtualDub and access file information.
Anyway, if your codec is earlier than DIVX5, you might need a small utility called SMR that fixes exactly the same problem for "old codec" files.

I used the tmpegEnc software to convert my *.asf file to *.mpeg file..the video is converted, but with no sound...I try to locate the audio source to that *.asf file...but it just said 'can't open...or unsupported'...what can i do to convert this file with sound? Thx.

Tmpgenc usually will not encode the Audio from ASF/WMV files..But you Can encode the Audio seperately and Mux it with the Mpeg Video...What I use with WMV/ASF files to get the audio is a Freeware Program called "DB Power Amp" you can download it at "www.dbpoweramp.com" and Download the WMA codec and the "MP2" codec, and rename the "ASF" file to "WMA" then encode it to either WAV or to MP2..If you encode it to MP2 you can just load the Mpeg video file you allready encoded into the "Simple Multiplex" and Load the "Mp2 file in also then click "Run" and it will Mux the 2 files together ,But if you encode it to wav you will need to encode the WAV file to Mp2 with Tmpgenc of some other audio encoder....

I have this movie but i want to erase the bottom of the screen because when i play the movie,we see some information at the bottom and i want to delete that so i can see the movie without having to see that info in my dvd player when i copy it as vcd format.Is there a way to delete that part of the screen with tmpgenc or some other programs.Help will be greatly apprecieted.

You can"t "Erase" it But you can Cut it out..Go to the "Settings" to "Advanced Settings" to "Clip Frame" and From there you should be able to figure it out...

I have purcheased tmpgenc plus and i have had problems opening mpg2 files ever since version 2.57 came out. I have a fully licensed version of Ligos encoder installed that i just purchased. I have set the Ligos vfapi plugin priority to 2, i have uninstalled tmpgenc plus , Ligos encoder, reinstalled even resinstalled Windows XP. I know the mpg files are godd because Tmpgenc 2.6 will open them without problem. I am at my wits end. I read a lot of posts in the newsgroups about this same problem so i know i am not the only one. Can someone please help

Thanks
greg

If these are Mpeg2 files then The best and fastest way to encode them is useing DVD2AVI to make a D2V file out of the Mpeg2 file then encodeing that..I have no problems loading Mpeg2 files into Tmpgenc But I still Use DVD2AVI to frame serve them Cuz it is a much better Mpeg2 decoder...Sometimes De-Muxing the Mpeg2 file and Just loading in the M2V file works..You don"t need to encode the audio anyways Cuz it is allready in the Correct format for VCD/SVCD/DVD and encodeing it again will just degrade the quality and in some cases can Cause Sync problems...

I have upgrade from tmpgenc 2.01 to 2.58.44 plus. Since this, I cannot convert avi to mpeg with out errors like "Write error occurred at address 77f536f7 of module 'ntdll.dll with 00000000" I have tried three seperate files. Help?

I've been having the same sort of problem .. but I get 'Read Error Occured'! Check out my thread on the next page called "Read Error Occured ..." . I have just tried the Panasonic MPEG 1 encoder, and that seemed to work fine!!
Cheers, THM

Are you using Win XP?
Are you using Nimo codec pack? And it is the latest one?
If the second condition is true, then here is your problem.
In that case you will need to get back to pack 4 or 5.
it will fix it.

Dude, if this works, I love you, I'm downloading Nimo 50build8 bundle. I have Win XP and I get that stupid error too. Will that version on Nimo work?