This forum is for users to exchange information and discuss with other users about a TMPGEnc product.
In case you need official support, please contact TMPG Inc.
Pegasys Products BBS [ Sorted by thread creation date ]
hello again
i have gone through virtual dub went to save wav however the wav creted does not play and just shuts down the programme im running it in is there anything i can do or is just bad divx file?????
thankyou.
If you have a DIVX file, why not run it through DVD2AVI to get the MPEG audio file which will be have an .MPA extension, I believe. You can convert that MPEG audio file to a .WAV file using one of the many programs available on the web. Or, you can use the resulting files and use TMPGENC to encode the video to VCD.
The audio you are trying to extract from the DiVX movie may not be compatible with Virtualdub. It is likely to be Ac3 which is not compatible with Virtualdub.
To extract the audio from the DIVX to a wav use AVIMUX.
I'm using AMD Athlon 1800+ & DDR RAM 256MB running on Win2k SP 2. When I tried to encode a 13GB AVI to VCD PAL format using best quality and the system always halted half-way thru. Please advice. Thanks.
Hello, how much hard drive space do you have. Is your Windows Temp directory full of garbage files? Or, your network temp directory full up, too? I would run a good system diagnotic tools program such as Norton Utilities or Ontrack to clean up the registry, temp directory, space hogging files that aren't needed, etc. Especially, if you've never done this before.
Windows sub directories are limited to the number of files that can be contained in them, which is why most power users put the working Temp directory under the C: root. Windows then allows for almost unlimited garbage files here, and you can easily see and clean them out.
If the File stops Encodeing at the same spot every time then there could be a Glitch or error at that point of the file..You can try encodeing up to were it stops then start encodeing again a few frames after were it stoped then join the 2 parts together with the merge & Cut....
>Hello, how much hard drive space do you have. Is your Windows Temp directory full of garbage files? Or, your network temp directory full up, too? I would run a good system diagnotic tools program such as Norton Utilities or Ontrack to clean up the registry, temp directory, space hogging files that aren't needed, etc. Especially, if you've never done this before.
>
>Windows sub directories are limited to the number of files that can be contained in them, which is why most power users put the working Temp directory under the C: root. Windows then allows for almost unlimited garbage files here, and you can easily see and clean them out.
>
>Seasons Greetings.
>
Hi,
Thanks for your reply. I don't think is due to hard disk space. I have 60GB empty space, that should be more than enough.
>If the File stops Encodeing at the same spot every time then there could be a Glitch or error at that point of the file..You can try encodeing up to were it stops then start encodeing again a few frames after were it stoped then join the 2 parts together with the merge & Cut....
Hi,
Thanks for your reply. I'm using Ulead VideoStudio 6 and using "DV Video Encoder -- type 1" to generate the AVI file. The file actually does not accept by V-Dub and the error message is "cannot locate decompressor for format 'dvsd' (unknown)". Could it because of the "DV Video Encoder -- type 1"?
FYI, the output for "DV Video Encoder -- type 1" is 24 Bits, 720 x 576, 25 fps and DV Audio -- PAL, 48.000 kHz, 16 Bit, Stereo. Thanks.
Has anyone tried using an AVI or MPEG produced in
VideoWave 4, imported into TMPGEnc for DVD authoring?
It is not clear from VW4 if the format is Type-1 AVI
(w/ the known problems), however, there is an
option for Cinepac codec for Windows AVI in addition
to the DV AVI which I am guessing is type 1. Any experience
out there?
You get this error when you Haven"t go all the Tmpgenc Files in the same folder...All the Tmpgenc Files have to be in the same folder and one of tyhose files has to be the "P3P Package.dll"....
My project is an old wedding video, i used Premiere 6 to edit clips and deleted the original audio and replaced it with various music files. I compressed this to mpeg1 vcd-non standard via Avisynth frameserver with the following specs:
Tmpeg 2.57
352x240 29.97 fps
CQ min 1500 max 3000 quality 75
VBV buffer 40, Motion Quality: High quality
GOP Structure - don't think it will matter
Audio - Stream Type MPEG1 Layer II - (no idea why i used II instead of I)
44100 stereo 224 bitrate
The first song was compressed perfectly/flawlessly the second up to the fifth song there was a bit stuttered on the first few phrases and gets better until the song ends. Percentage wise about 3-5% of the audio is stutered.
This could have been acceptable, however i produced the video to be a romantic theme but the stuttering distract my viewers and ruin the rhythm of the story. I made another compression this time doubling the min to 3000 and max 6000 and audio bitrate down to 160 everything else is the same. What transpired is that the first song again is flawless, the rest of the song has stutters but instead of the first part it moved somewhere in the middle of the song and the stuttering increased to about 10%.
Im lost where else i can adjust to improve the audio. BTW in PC playback its perfect. My DVD/VCD player is Pioneer DV-C503.
The DVD player certainly can't handle the non-standard VCD format that you have choosen, and is getting totally confused with the data rates. To guarentee that the DVD player will work properly encode the VCD so that you don't exceed a video encoding rate of 1150 bps. A CQ_VBR setting of 1150 for MAX, 0 for MIN and 100 percent quality should suffice and allow you to get about 90 to 95 minutes of video compressed enough to fit on 1, 80 min CDR.
I'd also check your owner manual for the DVD player for its specs and check with Pioneer as well. Some newer players will handle some of the weird, experimental bitrates that people are trying to encode into VCD, but to ensure the maximum capatibility 1150 bps will suffice for encoding VHS tapes to digital. Unless you have a lot of superspeed, hiaction, graphics special effects going on, no one is going to notice.
Also, the Noise Ffilter setting of 8, 2, 8 or 4, 2, 4 (depending on how noisy the video is) with High Quality set does an excellent job of smoothing and helping the resize filter crunch the file a bit more than without the filter. It does slow encoding down up to 400 percent, but the results are worth the effort.
Your problem is probably linbked to your bitrate. Your player doesn't seem to be able to handle the max bitrate you have chosen. A lot of DVD players have a limit to the bitrate they can handle. It is probably limited to 2600kb/s. Drop your max bitrate down. You can find a good list of what DVD players can handle at VCDhelp.com in the DVD player list. Your player will probably be listed.
Also another important point is the VBV buffer size you have chosen. 40 is too low for the bitrate you are using. The VBV buffer size has to rise with bitrate and 40 is for standard VCD. The buffer size you should be using should be at least double that. About 112 should be ok.
If you set it to '0' then TMPG will automatically chose the appropriate bitrate for you.
Hello, i relatively new to this program. I have an 800 meg mpg file. I want to put on 2 cdr...cutting the first half was really easy...however for the second half... it always gives me 73 megs file instead of a second 400 megs file...no matter where i set the start and end cursor...why....been trying for hours :(
Hello, you didn't say which version of TMPGENC that you are using. But, MPEGS aren't really designed to be diced and chopped, split and hacked, TMPGENC does a great job, but somethings things can get really messy depending on how the MPEG is encoded, structured, etc.
Why don't you just encode the video into 2 sections with the encoder instead of the MPEG tools? Just set the start and end marks for the section to encode and voila! Yes, it may take longer but it works for everytime. Since you have the first half cut with the tools, just encode the second half with the encoder and you're done.
Especially those movies that you know that you'll have to split. Just encode each section into 80 minute chunks, or thereabouts. Most movies have fades to black where commericals will be inserted at reasonable breaks, so you may have a fade close to 75 or 78 minutes, etc., etc. throughout the movie. So, you actually do 2 or 3 encodes of the various sections. Saves the hassle of trying to use the MPEG tools after the encode.
I used the wizard in TMPGEnc and reduced the Average video bitrate and the Audio bitrate so that the Estimated file size would be 694MB. But, after I encoded the AVI, the resulting MPEG was 986MB. Did I miss something?
There is a Bug in this Version if Tmpgenc That will not let you lower the bitrate lower that the standard VCD bitrate...If you use the Muxer of an older version it will take the extra Padding off the file so it will be smaller...
Hello. If you want to get a 90 minute movie onto an 80 minute CDR, try a CQ_VBR with 1150 MAX and 0 MIN with 100 for Quality and lower the audio bitrate to 128 Kpbs.
But yes, normally an 89 minute VCD at 1150 Kpbs video rate and 224 Kpbs audio rate won't fit onto an 80 minute CDR. If you have just 9 minutes to crunch down, just reduce the audio rate first to 128 Kpbs. There are various calculator programs that will allow you to play around with video and audio bitrates. There's an equation on this site for simple VCD guestimates, and other programs can be found by just doing a google search, or just go to VCDHELP.COM to start learning about this topic from the ground up.
I agree, reducing the audio bitrate to 128kb/s and using the CQ VBR method and also overburning to 82mins, you should be able to fit this 89min movie on to 1cd even though the quality will leave a lot to be be desired.
Standard VCD bitrate is pretty crap to begin with and reducing it any further will make it worse.
The CQ method shouldn't make it any worse than standard VCD though, but my advice would be to split this movie to 2 disks and increase the max bitrate to 3,500 using the CQ method.
Hello. I am encoding some files to make into a VCD. In the past, the movies come out fuzzy(but it is still clear) when it appears on the TV. How do you increase the quality when encoding files? If you can, please explain to me about the motion search precision option because I don't get it. Currently, I have it on "Highest Quality (Very Slow)" but it will take me 4 hours and 20 minutes! Is there another way that has good quality and is fast?
The Motion Search precition is setting is so the encoder reads ahead to it can predict motion and the complexity of upcomeing frames the higher you set it the farther ahead it reads, but haveing it on the Highest Setting doesn"t really help, it is not any better than the High setting, but to increase the Quality the best thing you can do is increase the Bitrate, but this will also increase the file size....
How/where do I increase the bitrate? Can you show step-by-step please? What I did was I first went to "Load" and clicked on "VideoCD(NTSC).mcf" or something like that. After that, I cannot switch to something else in the Rate Control Mode because it's fixed at Constant Bitrate(CBR).
How/where do I increase the bitrate? Can you show step-by-step please? What I did was I first went to "Load" and clicked on "VideoCD(NTSC).mcf" or something like that. After that, I cannot switch to something else in the Rate Control Mode because it's fixed at Constant Bitrate(CBR).
It you click the Load button the main screen then navigate to the Templates folder then to the Extra Folder then load the "Unlock.MCF" Template, Now all the settings will be unlocked, now click the "Settings" tab and go to the "Video " Tab then raise the bitrate..if you raise it to 1600kbs the Quality will get a lot better But you will only be able to fit about 60 minutes on a CD-R....
You said that the encoded VCD video was "fuzzy" but "clear" which are contraditions in terms. What was the type and quality of the original video source? Also, don't forget that you are downsizing the video to 352x240 which will amplify any defects in the original source.
Yes, the encoded video will look "softer" or less "sharp", but you can only tell the difference because you are comparing the two videos. Let's not get so nitpicky. You are using a medium, a CDR, that wansn't designed originally for what we are trying to burn onto it. If you want "sharper" quality encode in DIVX and burn to a DVD, and don't use video tapes as the source.
>You are using a medium, a CDR, that wasn't designed originally for what we are trying to burn onto it
What has the medium got to do with the quality? The only way the medium will affect the image is if your player cannot handle the bitrate on it or it has been burned incorrectly.
>If you want "sharper" quality encode in DIVX and burn to a DVD, and don't use video tapes as the source.
DIVX is not DVD compatible and not everbody has a DVD burner.
My advice if you want better quality images is to encode to XSVCD MPEG2 using the CQ VBR mehod.
If your player supports it, use the bitrates:
Min- 1800 kb's, Max- 4000kb/s and Quality- 65%
VBV buffer- 224
Resolution- 480x480 NTSC or 480x576 PAL
Motion search- High quality
This should allow you to fit a regular 100min movie on 2 disks.
If your player struggles with playback then you will need to reduce the max bitrate to an appropiate level which your player can handle.
I have the 2.58 plus version. Now I am concerned as I have reading about issues with 2.59 related to bitrates and file sizes but have used it with no real issues that I can see since its release.
Hello. I am encoding some files to make into a VCD. In the past, the movies come out fuzzy(but it is still clear) when it appears on the TV. How do you increase the quality when encoding files? If you can, please explain to me about the motion search precision option because I don't get it. Currently, I have it on "Highest Quality (Very Slow)" but it will take me 4 hours and 20 minutes! Is there another way that has good quality and is fast?
I cannot open mov files for TMPGEnc. I downloaded the plugin, and the directions say to copy it to the TMPGEnc folder, i tried it, but i still get the error of "can not be open, or unsuported". please someone help me.
Go to "Options" to "enviromental Settings" to "Vfapi Plugins" and see if the Mov Plugin is listed in the Plugin List..and if it isn"t then it wasn"t installed properly and if it is there then try raiseing it"s priority....