This forum is for users to exchange information and discuss with other users about a TMPGEnc product.
In case you need official support, please contact TMPG Inc.
Pegasys Products BBS [ Sorted by thread creation date ]
ok I saw the answer somewhere here before But I have movie files that hang up after encoding...I saw someone post a link to a file that fixes these hanging up vids but I cannot find it..any help is Greatly Appreicated..
I am having problems with coverting files to a VCD...The pixels are large and blocked it makes the picture flicker as the pixels move. Does this make any sense to anyone or am a complete newbie?
Techno your solution will not be insulted if you just respect the advice others give.
Like I said everyone has there own solution and not any one solution is the final end. It is up to the receiver of these solutions to decide which is best for him not you.
In trying to convert a 114 minute video to two VCDs, I must convert half of the video twice. The first half works fine; I set the source range from frame 0 to 107374.
For the second half, I set the source range from frame 107304 to the end. However, when I start the encoding, TMPGenc starts at frame 0 again!
I am using TMPGenc version 2.53.35.130, downloaded yesterday. This problem happens if I don't use the Wizard. If I DO use the Wizard, everything works OK.
please help me im trying to convert divx-clix files to mpeg1,but i cant get no soud,same problem i have with some avi files to meg1 or meg2
send me a mail at lienbjornchello.no
i'm trying to convect a movie but when i open it with tmpgenc the output will have a .m1v and when i try to change it to .mpg and encode it it will say cann't open or unsupport
When I select 'FILE'
'Preview'
The box opens and my video is cut off somewhat. The Moive I am Backing up is Atlantis. The title screen opens, but when the words come on the screen I can only see the right side of the preface to the movie.
What am I doing wrong? It seems like the movie should be almost twice as wide.
I am converting an avi(divx) to .mpg and during the conversion, the program just closes on me. I tried again, and it stopped again at the same part. I'm not sure if there was an error message or anything when it stops because i was afk at those times. If anyone knows why its doing this, plz let me know, thx. (eg.)Is this a trial version or something?
I have been struggling over the past couple of weeks with the "no sound" problem when converting from .avi to .mpg. It is possible that for some reason my problems began after upgrading to TMPGEnc 2.53.35.130.
I was able to solve the problem by going to Option/Environmental Setting... and clicking on the VFAPI plug-in tab. I suspected that multiple plug-ins for .avi support was the culprit. In my case, I had the AVI2(OpenDML) File Reader (checked, priority=0) and AVI VFW compatibility reader (checked, priority=-2). All I had to do was uncheck the AVI2(OpenDML) File Reader and the conversion went fine with audio.
I'm sure that there may be cases where I need to check the AVI2(OpenDML) File Reader, but for most of my current encoding purposes, this change seems to correct my problems.
I am trying to convert AVI->MPEG, MPEG->MPEG but the program just hangs entire computer. Have this phenomena in VIRTUADUB as well... Could it be some hardware error? Anyone have any idea?
I am getting an error every time that i try to cut a MPG in MPEG Tools. The error is "Could not initialize DirectShow. (0x80040154)". I've Reinstalled Direct X 8.1, TMPGEnc 2.53, and Nemo Codec Pack and it still gives me this error when i load the mpg in "Merg & Cut", highlight it and press the edit button so i can set the start and end points. Does anyone have any idea as to what i can do to fix this error? Thanks alot.