I would like to string together a time lapse sequence of JPGs using TMPGEnc. It has been suggested to me that this program will do the job for me but I can't work out how.

Is there a FAQ, help file, that will be able to help me?

Thanks in advance.......

Make sure the JPG's are numbered sequentially then just load the first JPG in the sequence.

I would like this marvel proggy to be able to do this:

1.- Set a track as first play, with appearing in the menu. I'm actually solving this by moving the button for that track out of the safe areas but remote control number still works as well as navigation.

2.- I also would like to insert some videos as transition between menus and between menus and the movies.

That's all. Hope I explain myself clear. English is not my mother language.

Regards,
Khonshu.

Hi folks -

I'm having some issues with getting TMPGEnc to startup VobSub and use the subtitles for an MPEG-1 format movie that I have - I want to use it to "burn in" the subs.

1. I have set the priority for the DirectShow Multimedia File Reader to the maximum (3) in the Environmental Settings dialog box.

2. VobSub does load properly and show the subs when I run the movie in Media Player.

3. The subtitle filename and the movie filename are the same (except for the file extensions of course), and the files are in the same folder.

I've reinstalled TMPGEnc a couple of times to make sure there was nothing wrong with it.

Any ideas?

Thanks!

Install FFDSHOW.

@ashy. I have the same problem. I also tried ffdshow. didn't work.

Following is my comment to a similar thread somewhere else on this board. (Question: No subtitles?! NO 2751 started by Sakin on 2004/04/25).

I have recently run into the same problem with TMPG. I used to be able to burn all subtitles into my movies with Directshow VFAP set to highest priority and installing DirectVobsub. Was doing this for over a year with TMPF successfully encoding evefrything I threw at it. Started having problems with XVID encoded AVI's. Since more and more movies were coming out in XVID, I searched the forums of Videohelp.com and several other places and they all came up with the same suggestions. Uninstall the Nimo pack codecs (which I used succesfully for quite a while), install ffdshow, configure its codec for XVID, turn on the subtitle option in ffdshow etc. Did not work. The subtitles load automatically in the media players but not in TMPG anymore. Now I can't get TMPG to hard burn any subtitles at all. TMPG doesn't seem to load directshow anymore. I believe I somehow screwed up a registry or TMPG setting. BTW, presently I have the K-Lite Codec pack installed (although I installed the newes XVID codec and the newest Vobsub and directvobsub directly from files obtained throuhg their websites). Every thing seems to work OK except I CAN'T GET TMPG TO LOAD THE SUBTITLES. Would appreciate any suggestions.

I want to post small video clips for my movie review site. I *was* using my video editing software's default .wmv export, but it's not exactly the most widely supported format.

But first I need to figure out how to get a comparable balance between filesize and sound/video quality. Ideally, the 10-30 second video clips would be small enough for a 56k modem user (like me) to download.

Here's a short (128k) clip from my site: http://ironicconsumer.com/movies/mazes_couldbeparents.wmv

So, basically my question is, what settings do I use to compress an .mpg of comparable quality?

When I attempt to convert my Xvid file (717mb), TMPG is showing 7885mb. This is using a 3000 bit rate. While encoding, it is also showing 10hrs. Is this correct. I had 8% of the file encoded and it was over 600mb. How will this fit, and is this the normal time? Thanx for the help.

when i try to convert to svcd only the sound is outputted.no vision.i've checked everything a million times over(frame rates etc..).the original file is a torrent avi file which plays perfectly in media player.its just when i try and output it to svcd.any help appreciated.......lee

Raise the priority of the 'Directshow file reader' to 2 or 3 in the VFAPI plugins.
If that doesn't cure it install the latest FFDSHOW.

Hi,

i ahve the following problem:

I downloaded the Episodes of 24. Now i want to burn them on a Video DVD. For this i have to change the Format to mpeg-2. If i start the conversion, everything seems to be fine (and at the first two episodes it was fine), bat after the first commercial break, which was cutted out, the screen fades out to black and then will be black the next 30 Minutes. What can i do?

I am converting some MPEG-2 NTSC (TV recordings) files to VCD. Often when I move the slider or scan forward with the >> << buttons in the Source Range window, TMPGEnc will hang. If I close the program and restart it, often I can scroll back and forth with no problems, so the problem is pretty random.

Some files were created with a Hauppauge PVR-250, others with an ATI TV-Wonder and BeyondTV. Makes no difference where the files come from, all can hang the program.

HELP?

bump.

The problem
I have a Sony DVD recorder (RDR-GX3) and a Sky+ box (satellite receiver/decoder with integrated hard disk), I wanted to be able to record my favorite films and TV shows onto a DVD-RW disk and then edit them on my PC to cut out the adverts etc.

I bought a Plextor PX-708A DVD writer (for my PC) and looked for some software that would allow me to edit the VOB files, I deceided on TMPGEnc DVD Author because I liked the layout of the software, then however the problems began.

Firstly the Sony DVD recorder can format the DVD-RW disks into DVD-Video or DVD-VR, I picked the former because it has greater compatibility with commercial DVD players, unfortunately the "Add DVD video" button on DVD Author will only work with commercially pressed DVD's and not ones from DVD recorders and the "Add file" did not work either (there is a note to this effect in the help file), so I tried a film recorded in DVD-VR format and found that my PC would not read the disk correctly. This is a problem with Win XP (it is mentioned in the FAQ section for DVD Author on the Pegasys inc website, for more detailed information see knowledge base article 818733 on the Microsoft web site).

Solution number 2
Download the Instant Read 6.5 file from www.pinnaclesys.com (do a search for "Instant Read 6.5" on the home page. DVD-VR disks are basically a UDF format, Win XP does not read the DVD version correctly, however I found that after installing this software, I could insert my DVD-VR disk, run DVD Author and select "Add DVD video" and it worked fine.

PLEASE NOTE - I have only recently discovered this second solution so I have not tried it out as extensivly as solution number 1, I origonally had the Nero InCD software installed on my PC (a previous failed attempt to get a DVD-VR solution) and found that it clashed with Instant Read, I think it would be safe to say that it is not advisiable to have other UDF readers installed on your PC.

I hope that you find this post useful - Happy editing

SDR

>The problem
>I have a Sony DVD recorder (RDR-GX3) and a Sky+ box (satellite receiver/decoder with integrated hard disk), I wanted to be able to record my favorite films and TV shows onto a DVD-RW disk and then edit them on my PC to cut out the adverts etc.
>
>I bought a Plextor PX-708A DVD writer (for my PC) and looked for some software that would allow me to edit the VOB files, I deceided on TMPGEnc DVD Author because I liked the layout of the software, then however the problems began.
>
>Firstly the Sony DVD recorder can format the DVD-RW disks into DVD-Video or DVD-VR, I picked the former because it has greater compatibility with commercial DVD players, unfortunately the "Add DVD video" button on DVD Author will only work with commercially pressed DVD's and not ones from DVD recorders and the "Add file" did not work either (there is a note to this effect in the help file), so I tried a film recorded in DVD-VR format and found that my PC would not read the disk correctly. This is a problem with Win XP (it is mentioned in the FAQ section for DVD Author on the Pegasys inc website, for more detailed information see knowledge base article 818733 on the Microsoft web site).
>
>Solution number 2
>Download the Instant Read 6.5 file from www.pinnaclesys.com (do a search for "Instant Read 6.5" on the home page. DVD-VR disks are basically a UDF format, Win XP does not read the DVD version correctly, however I found that after installing this software, I could insert my DVD-VR disk, run DVD Author and select "Add DVD video" and it worked fine.
>
>PLEASE NOTE - I have only recently discovered this second solution so I have not tried it out as extensivly as solution number 1, I origonally had the Nero InCD software installed on my PC (a previous failed attempt to get a DVD-VR solution) and found that it clashed with Instant Read, I think it would be safe to say that it is not advisiable to have other UDF readers installed on your PC.
>
>I hope that you find this post useful - Happy editing
>
>SDR

The problem
I have a Sony DVD recorder (RDR-GX3) and a Sky+ box (satellite receiver/decoder with integrated hard disk), I wanted to be able to record my favorite films and TV shows onto a DVD-RW disk and then edit them on my PC to cut out the adverts etc.

I bought a Plextor PX-708A DVD writer (for my PC) and looked for some software that would allow me to edit the VOB files, I deceided on TMPGEnc DVD Author because I liked the layout of the software, then however the problems began.

Firstly the Sony DVD recorder can format the DVD-RW disks into DVD-Video or DVD-VR, I picked the former because it has greater compatibility with commercial DVD players, unfortunately the "Add DVD video" button on DVD Author will only work with commercially pressed DVD's and not ones from DVD recorders and the "Add file" did not work either (there is a note to this effect in the help file), so I tried a film recorded in DVD-VR format and found that my PC would not read the disk correctly. This is a problem with Win XP (it is mentioned in the FAQ section for DVD Author on the Pegasys inc website, for more detailed information see knowledge base article 818733 on the Microsoft web site).

Solution number 1
I recorded a film onto a DVD-Video formated disk and then used DVD Decrypter (go to www.dvddecryoter.com) to "extract" the VOB files onto the hard disk.

Firstly insert your DVD into the drive and run the software. On the menu bar select [Tools] [Settings], click on the [IFO Mode] tab and change the file splitting option to [None]. Then from the menu bar again select [Mode] [IFO I].
In the [Source] box select your DVD drive, and in the [Destination] area click on the folder + magnifying glass icon and set where on your hard disk you want the files to be stored. Next on the right hand side select the [Stream Processing] tab, ensure the [Enable Stream Processing] box is ticked as well as all the Video and Audio entries beneath it. Then do a mouse right click on one of the Video or Audio entries and click on [Set All - Demux]. Finally click on the DVD disk - arrow - Hard Disk button (bottom left) to start the process. Once this is complete on your hard disk you will have, amoung other things, two files, one with a .m2v extension the other a .ac3 file.

You can now run DVD Author, [Create new project] and then select [Add file], navigate to the .m2v file on your hard disk and select it. This brings up the [Add Clip] dialog box, press the [Browse] button in the [Audio settings] area and select your .AC3 file. Once you have edited etc you then get to the [Output] area, set you ouput folder and press [Begin output], when you do you get a dialog box saying [TMPGEnc DVD Author has encountered a problem], it is telling you that the combined bitrate is beyond the upper limit for the DVD standard. Select [Ignore] and continue on. (This message confuses me somewhat because I can see the bit rate on my DVD player and it is well within the limits, the only thing that I can think of is that DVD Decrypter puts something in the output files saying what the maximum bit rate can be and not any information about what it actually is).

I hope that you find this post useful - Happy editing

SDR

Hi all,

I'm just trying the newest version of TMPGEnc (2.521 ?) to convert DV-AVI files into DVD format. The program is great, the quality very good.

The problem is that TMPGEnc is crashing to desktop, without any error message.

Usually it happens at the end of the encoding process, leaving a working and complete MPG file but preventing from batch encoding (I'm making lots of short DV clips and the batch encoding is almost a must...).

Out of 20-30 encoding done till now, only 2-3 times the program did not crash and continued the batch, although it took 2 minutes after completing the MPG, before returning control and continuining the batch.

I also have crashes during the encoding, leaving an useless 0Kb MPG file on the hard drive. These crashes were not frequent until yesterday, but now they're so frequent that I could not encode my last AVI in 6 attempts (and it's still there to be encoded).

What I already checked:
- It's not memory/disk overflow (temp and output files are on an empty 80GB HD)
- RAM banks have been tested with docmem for 5 hours, no errors reported
- Other programs (including games and other encoders) don't give any problems
- No virus reported by McAfee (DAT files is 1 day old)
- No programs running in background, also system restore is disabled

I'm encoding DV-AVI files captured through Windows Movie Maker (my Pinnacle Studio 1.10 has been abandoned since when I installed XP Pro), but this shouldn't be the problem because, when the TMPGEnc works, the output is OK.

My system:

Q-TEC 550W Dual Fan Gold -
EPoX 4PDA3I i865PE FSB 800 -
P4 2.6GHz HT FSB800-
2x512Mb DDR400 Dual Channel -
GeForce4 Ti 4600 (Omega KX 1.4523a) -
Realtek AC'97 Audio -
QUANTUM FIREBALLlct20 40GB –
Maxtor 6Y080L0 – 80GB
Win XP Pro + SP1&2 + all security patches

Update:
the problem was the DV-AVI format produced by Windows Movie Maker.

Since this format is not read by AVI2DVD, when I used AVI2DVD usually I converted the files with the Canopus DV Converter (using the "Canopus Reference AVI" as output format)

I tried encoding the "Reference AVIs" with TMPGEnc and now everything works: at the end of each MPG the program returns control and eventually proceeds to the next file in the batch. Also the "shutdown at end of the batch" is working correctly

Hope this info is useful also for someone else, I'll spread the news around, since I've found several other people in this and in other forums having the same crash issue...maybe they can solve it in the same way.

Bye, Corrado

I have the same problem, but with Type-1 DV-AVI from MediaStudioPro.
What is strange is that I used to have no problem with this ....even though TMPGenc site now reckons it can't cope with Type-1 at all.
I guess something has been lost in a version update.
Next stop, to check if the new TMPGenc 3 supports DV Type-1.....

File : 190 MB (190 MB), duration: 0:34:23, type: ASF, 1 audio stream(s), quality: 34 %
Video : 175 MB, 712 Kbps, 12.79 fps, 640*480 (4:3), WMV3 = Windows Media Video 9, Not checked
Audio : 16.21 MB, 65 Kbps, 44100 Hz, 2 channels, 0x161 = Windows Media Audio 9, Supported

This is the original source file that I have. Is there any point in increasing the bitrate to a higher number? I beleive that this would just make larger file but not improve on the quality of this file.Infact other than applying sharpness filters or noise filters there is not much improvment to be had. Are there any experts that would give me a pointer for the best approch when converting these files to be stored on a DVD (using a DVD at this bitrate means I can store larger number of VCD quality mpegs?) but quality will not be improved over the original file. Right?

Right and wrong.
You cannot compare bitrates between different formats.
What may be OK for one format may not not be a high enough bitrate for another format.

WMV has a good compression>filesize ratio. This same ratio does not apply to MPEG1/2.
While the compression for MPEG1/2 is good it is not as good as WMV or MPEG4.
If you try to encode an MPEG at 712 kb/s it will look awful.

If you do not want to degrade the quality any further then it is best to use at least the same resolution, in this case you would need to use standard DVD resolution 720x480 and a higher bitrate. In fact I would use standard DVD bitrate settings.

You also have another problem. The frame rate is wrong. If you attempt to convert to DVD from this frame rate you will have playback problems. TMPG does not do frame rate conversion too well.

However you could try using the frame rate setting 25 / 2 = 12.5 but you would then need to set the resolution to 720x576 as this is a PAL frame rate.

The nearest frame rate setting for NTSC is 29.97 / 2 = 14.985 however this will still cause playback problems unless you speed up the original frame rate to 14.985 fps first.

In any case looking at this movie it seems pointless even bothering as it's such low quality in the first place.

So what you are saying in essence is to use the standard NTSC DVD template, however I amy have some issues with the frame rate as my original is non standard.
The standard bitrate for a NTSC DVD in TMPGE is CQ max 8000-2000. This is fine I have tried it and it does give good result to date I have not had any frame rate issues other than a time issue. Would re-encoding the this file throu MS movie maker help in getting a good frame rate better suited for conversion with TMPGE.

As usual more knowledge means more factors to decide from. I did not know that frame rate is not applicable to all media formats. Thanks again for your time and info.

Re-encoding your clip with MS Movie Maker will only make your clip look worse. It is a really bad idea to keep compressing your clip over and over. You want to put your cleanest most uncompressed into TMPGEnc.

That clip has a very unusual frame rate. I don't think you will ever get a smooth playback of that clip if you convert it to DVD, especially if the clip has a lot of panning side to side. There is professional software that will perform frame interpolation to adjust the framerate but I never used it so I can't say how it does.

Where did the clip come from? Perhaps you can get the original uncompressed source and encode that.

There is a saying: Garbage in, garbage out.

I think that the saying is right!! At this point all I am trying to do is to clean my HD of all the files I had, I just wanted a format that would remain the closest to my original(the original was probably a mini-dv it was then encoded to ASF for broadband diffusion using a standard template) so I am stuck with this unusual format as my source. At this point I will probably just load it into Tmpge and ask for a DVD NTSC 4:3 format conversion using the standard template. Since the consensus is that I will not be able to improve the quality the aim is to preserve what I already have.

Thanks again to all the positive insight.