This forum is for users to exchange information and discuss with other users about a TMPGEnc product.
In case you need official support, please contact TMPG Inc.
Pegasys Products BBS [ Sorted by thread creation date ]
I'm trying to make a dvd file, but the output file will be 118 percent of the dvd's capacity, and I cant set it to 90 percent of the disk (looks like the function is disabled) the original file is about 900mb , I want to convert it to Pal 16:9 625 line.
I've been trying to the trial version on both Intel and AMD based system; while on the AMD Athlon 4600+ X2 system I get application error when I try to encode any kind of material with multipass enabled. Same procedure works flawless on a ThinkPad T60.
The DivX codec is now at version 6.8.2 as of May '08. My TMPG Xpress is still encoding with version 5 of DivX. How can I upgrade my TMPG to run the latest version DivX codec?
What you'll need to do is install the latest divx codec. Then use AVI file output in Tmpgenc. From here use the latest Divx codec. Adjust the settings to your liking and encode.
If you want to do a 2 pass encode. You'll need to use the batch mode. For example, your first encode will be set multipass 1st pass. Then your second encode you'll use the Nth pass. The Nth pass will be your finished video file.
ok, very simple, unsitall ALL versions of divx that you have to ensure a clean installtion of the new divx, reboot when unistalled, do system clean with any systemc leaner you have i woudl normally go for tune up utilities with its reg cleaner, then install the neweest divx , make sure tmpgenc is closed, and then when your finished open tmpgenc and it will encode in the newest format.
Just installed TMPGEnc4XP.exe and received arror code "The instruction at "0x7c910de3" referenced memory at "0x3250564f". The memory could not be "read". Click on OK to terminate the program.
Got the same problem with application error on a Athon 4600+ system and applies with I enable multipass during encoding. Interesting enough same version of the trial works perfect on a Intel system...
I had the same problem. Somehow it appeared to me that it is a problem with a corrupt plug-in which TMPGEncXP4 loads - in my case it was an old/corrupt QuickTime. It un-installed the old QuickTime and installed the latest version - after which the problem is resolved.
I am getting the following error when I try to burn a movie to DVD:
"there is no usable DVD writing drive installed". Nero or IMGBURN works just fine and allows me to write DVD's but for some reason TMPGENC will not. Any ideas?
First a friend a mine had this problem an there was no way to fix it. Now I'm stuck with this too. I've set up an new PC system but installed the old DVD drive witch worked fine in my old system, but the Software does not recognize it now. So I guess it has nothig to do with the drive. Maybe with the way windows is installed (?) beause my friend an I are using a SATA drive as the boot partition. (In my old system I used an IDE drive to install Windows XP on.)
Hi I'm using tmpgenc 4.0 xpress to edit an avi file, that I only want certain parts of. So I edit it all in tmpgenc 4.0 xpress, that's fine. But the file is already encoded how I want it...so I just want to output with the same settings for video and audio just with the edit included (like direct stream copy in VirtualDub). But I can't find the equivalent in tmpgenc 4.0 xpress. Anyone help?
quite simple, you are altering the actual structure of the video and audio therfore are now unable to do a simple direct stream copy. As you have edited the video and audio it will now need to encode the video and audio.
Or dont use the product for this, go into nandub select the start and finish points of clip 1 , do the direct stream copy and save avi , this will save clip 1....do the follwoing process for all clips of the item you are editing, and then what you do is use nandub again but this time load clip1 and then use appen segment i believe its called and simple load clip 2 and so fourth. and then do direct stream copy etc.
how ever you re unable to do the direct stream copy if you alter the audio bitrate, or the aspect ratio or res of the video via its filters, and again this is becuase you would have altered the structure of the video, and if you did this you would essentially need to encode the final product when all clips are together.
if how ever this is a tv capture, then the encoding when all together isnt abad idea as you would need to use the cropping/resize filter to crop the borders.
I have tmpgenc express 4, I encode my videos en dvd standard mpeg file, all it is OK, but when try to create a DVD with 2 or more movie(Tmpgenc dvd autor 3), show an error:"could not open the video part of the file xxxxx(Path).. only the audio part can be opened", Help me please! I have installed windows vista businnes 64 bits, I need a codec?
In my case, I could correct this error by changing settings in DivX codec. I went to Start -> Programs -> DivX - DivX Codec -> Decoder Configuration Utility. Once there, in the "Decoder" tab I unchecked "Support decoding of generic MPEG4-Video" option. I guess this option makes DivX codec the default codec for any avi file. So if you are trying to open a xvid file maybe it fails.
Hope this can help.
its normally a case of conflicting codecs, if you have more than 1 codec package and im talking about the codec bundles such as klite etc, do a clean unsiatll of them all, reboot do a clean system with like tunup , and then install the 1 select codec pack, this shoudl then solve the issue.
also at times its may be becuase of VBR mp3 audio,if thi is the case, use nandub to load the file, and save both video as direct stream copy which will then save only the video, and save wav .
so then when you load the video into the dvd authoring software, you can then load the wav and go forward
i ve tried to use the program to Convert Mkv files to DVD but most of the times there were audio sync problems in the final DVD, or the playback was not at the appropriate speed (slower video.. audio normal)...
Can u pls make ur program to be more compatible with MKVs?
I have tried TMPGEnc DVD Author 3 with DivX® Authoring, realy stable program but there are some lacking features:
- It would save alot of time if this program could do batch jobs for encoding more than one file.
Request:
* Adding feature for doing multiple jobs at the same time
- When I want to make a DivX disc from the correctly encoded DivX files(from this program),instead of joinning these files together the program converts these files again. This way takes very lo....ng time to create the disc and the quality would be loss again after the disc created.